 |
|||||||||
 |
Browning |
|
Colt 1911 |
|
Ruger |
|
Smith & Wesson |
|
Taurus |
|
||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| 10/22 INTEGRAMOUNT-One-piece ring and mount puts and end to misaligned scope rings and expensive scope damage. Places the scope in optimum alignment with the rings so they can't pinch or torque. Matches the factory hole spacing; ultra-strong design attaches in seconds with screws provided. Accepts 1" scopes with up to 40mm diameter objective lens. 4" long, available in black or silver, matte anodized finish, weighs 3 ounces. Mounting screws included (6-48 thread). | |||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| Finally a no drill and tap Weaver style scope mount. This mount requires no drilling or tapping of your receiver. Handsome, lightweight and durable. Blends beautifully with the lines of the rifle. Accepts all Weaver-style rings and accessories. 4-1/2" long, available in black or silver, matte anodized finish, weighs 1.3 ounces. | |||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
|
Mini-14 Ranch-Increase your scope options when
you install this lightweight, Weaver-style rail on your Mini-14 Ranch
Rifle. Lets you mount mini or short- length scopes as well as Tasco PDP4
or Aimpoint red dots without permanent modifications or Gunsmithing. Keeps
the scope low over the centerline of the receiver to maintain optimum eye
and scope alignment. Multiple cross slots allow adjustment for maximum eye
relief. Accepts all Weaver-style rings and accessories. 5" long, silver or
Black, matte anodized finish, weighs 2.6 ounces. Fits the following
Rifles: RUGER Mini 14 Ranch Rifle Deerfield Mini 30, PC-40, PC-9, Carbine and 10/22 Magnum |
|||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
|
WARNING: The .454 Casull and 480 Ruger Super Redhawk require our new SRH454 (below) mount for the heavier recoil they produce. Super Redhawk- Tired of the limited application of the Ruger factory rings that came with your Super Redhawk. Now you can change the Ruger mounts to a versatile Weaver-style rail in just minutes and with no permanents alterations to your gun. Lightweight, aluminum rail with steel integral, recoil pins attaches without drilling and tapping. Accepts all Weaver-style rings and accessories including the 40mm Tasco PDP4. Front and rear factory sights do not require removal. 5" long, silver, matte anodized finish, weighs 2.6 ounces. |
|||||||||||||||||||||||||||||
|
|
||||||||||||||||||
|
|
|||||||||||||||||||
| Same as the SRH+ but requires the removal of the rear sight. We use the rear sight notch as the recoil lug, as we do on most of our scope mounts. This mount is a more economical solution to the scope mounting issues on the large caliber's. This is a very attractive solution to the problem. | |||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| Drill & Tap- Remove the rear sight and drill and tap the top strap for just two screws then install this ultra-strong mount that will stand up to the magnum revolvers from Ruger. Accepts all Weaver-style rings and accessories. 4-1/2" long, available in black or silver, matte anodized finish, weighs 1.3 ounces. | |||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| REDHAWK and Blackhawk Hunter- Fits the NEW and Older Style Redhawks and Blackhawks with the integral scope ring cuts in the barrel. This is a no drill and tap mount for installation on the cuts made by the Ruger factory. Installs in minutes so you can add the scope or dot sight of your choice using Weaver style attaching points. | |||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| Finally a no drill and tap Weaver style scope mount. This mount requires no drilling or tapping of your frame. Handsome, lightweight and durable. Blends beautifully with the lines of the frame. Accepts all Weaver-style rings and accessories. 4-1/2" long, available in black or silver, matte anodized finish, weighs 1.3 ounces. | |||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| MkI MkII 22/45 No Gunsmithing- If you have and older MKI, MKII that's not drilled and tapped you can install this SCOPEMOUNT without making any permanent alterations to your favorite pistol. Remove the rear sight, insert the threaded dovetail filler and install the mount with the screws provided. Accepts all Weaver-style rings and accessories. 5-1/4" long, silver or Black, matte anodized finish, weighs 2.5 ounces. | |||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||
| MkII 22/45 Drilled and Tapped- You can pay more money but you can't buy a better, stronger mount for your MkII. Lightweight rail attaches in just seconds to pistols that are factory drilled and tapped. Provides a "rock steady" base that accepts all Weaver-style rings and accessories. Includes mounting screws. 4-3/4" long, available in silver or black, matte anodized finish, weighs 1.7 ounces. | |||||||||||||||||||||||||||||
|
|
|
Copyright © 1999-2009 www.GunAccessories.com All Rights
Reserved. |
|
